15-point winter prep checklist

Heating costs can throw a wrench into your winter budget — and the cold can make you cranky. But you can limit the discomfort by addressing the gaps, cracks and waste that drive up fuel costs. Such fixes are available at a lower price than you might imagine.

Run through this checklist of fixes this fall to make your house cozier and heating more affordable as winter approaches.

1. Install weather stripping.

Check your home’s exterior doors for cold air leaks. Do this from inside the house. The high-tech approach is to use a laser infrared thermal gun to detect cold drafts. The low-tech way is to move a lit candle around the door frame; the flame will blow toward you when there is a draft. Seal a drafty door by installing foam or felt weather stripping inside the door frame. Ask at your hardware store for the correct products and installation instructions.

2. Install a door sweep.

Use a door sweep to stop drafts from entering your home under an exterior door. A sweep is a flexible piece of rubber or plastic that’s held to the door’s lower edge by a strip of aluminum.

3. Seal attic air leaks.

Find and seal gaps that could be allowing heat to escape your home through air leaks. Pull back attic insulation to find and seal cutouts in drywall for electrical fixtures, pipes, fans and outlets. Also, check wiring, chimneys, flues, vent stacks and ducts, and seal them on the inside. Use caulk to fill smaller gaps and pressurized expanding foam for bigger openings.

4. Close the damper.

Heated or cooled air flies up the chimney when you leave the fireplace damper open. Make it a habit to shut the flue after the fireplace has cooled.

5. Add attic insulation.

Insulation keeps warm air inside in the winter and expensively cooled air inside in the summer. Typically, houses in our area should have a minimum R-38 insulation in the attic. Insulating an attic, basement or crawl space is moderately difficult, and beginners should hire a professional. Remember that DREMC offers a $250 attic insulation rebate if you use a member of TVA’s Qualified Contractor Network in the eScore program. Ask us for details at 931-680-5883 before you begin installing attic insulation. Admittedly, insulating is not a cheap job. But the payback can be huge! See Energy.gov’s guide to sources and a calculator that can help you estimate the return on an insulation investment.

6. Install a programmable thermostat.

A programmable thermostat can help you lower your monthly energy bills, too. The thermostat can save fuel by automatically lowering (or raising) your home’s temperature while you’re away. It also keeps temperatures consistent, saving fuel. Simple programmable thermostats start at about $50.

7. Set the temperature manually — and leave it.

You can enjoy fuel savings for free simply by setting your thermostat to one temperature in the morning, another at night and otherwise leaving the thermostat alone. If you’re chilly, put on a sweater and warm socks instead of raising the heat.

8. Seal furnace ducts.

Heating ducts typically waste up to 30% of the heated air they carry, losing it to leaks and poor connections under the house. Leaky heating ducts mean higher utility bills and a house that’s harder to keep warm. You may not be able to reach all the ducts — some are hidden in walls, ceilings and floors. But you can improve performance by sealing exposed ducts in the attic, crawl space, unfinished basement and garage. Focus on the places where ducts, vents and registers meet floors, walls and ceilings. Use mastic sealant, which is more durable than duct tape, to seal the seams and connections.

9. Replace furnace filters monthly

Dirty furnace filters reduce furnace efficiency and push up heating bills. They also shorten the life of a heating and cooling system. Check and replace the furnace filter monthly. If you’re not sure if it’s time to replace your air filter, hold the filter up to the light If you can’t see light through it, you need a new one. Pleated filters work best because they trap more dirt particles.

10. Keep your furnace running smoothly.

Servicing your furnace regularly helps you catch problems before expensive breakdowns, prolong the furnace’s life and keep it running more efficiently. Newer furnaces need professional servicing every two years. Older units require annual servicing. Check your furnace’s manual to see which specific steps are recommended. Ask friends and colleagues for names of good technicians. Find one or two you trust and stick with them.

11. Insulate the hot water heater.

Save energy by wrapping water heaters in a blanket of insulation. This is an easy DIY project that even a beginner can do. When insulating a gas or propane water heater, do not cover the burner access.

Do not insulate:

  • Pre-insulated water heaters. These are newer units with factory-installed insulation of R-16 or better (check the manufacturer’s label) under the metal shell.
  • Water heaters located where the added heat is welcome.
  • Water heaters whose manual or paperwork warns against insulating.
  • Tankless (on-demand) water heaters.
12. Make sure the water heater is set at 120 degrees.

Water heaters typically are set at 120 degrees when they leave the manufacturer. Lowering the temperature below 120 degrees could affect the sanitizing of dishes in the dishwasher.

13. Plug household leaks.

Grab a tube of caulk, a can of spray foam gap-sealer, a pencil and notepad. Tour your home, inside and out, including the basement, to find and fill cracks and gaps in siding, windows and foundation. Note locations of problems you can’t fix right away. Use caulk for small cracks and the foam sealer for bigger gaps. Inside the home, use a candle flame or digital thermometer to find where cold air is entering. Pay attention to windows, skylights, chimneys, vents and door frames (in areas around the frame not remedied by tip No. 1’s weather stripping). Also check openings around appliance vents, electrical and plumbing fixtures and furnace ducts and check the top of basement walls where the foundation meets wood.

14. Insulate water pipes.

Insulate the hot water pipes in your basement or crawl space by snapping foam sleeves on them. You’ll find pre-slit, hollow-core, flexible foam pipe insulation at hardware stores. Make a note of your pipes’ diameters and lengths, and bring the measurements when you shop. Exposed pipes waste heat by cooling the water as it runs through them. Be sure to include pipes between the hot water tank and wall. Also insulate cold water pipes for the first 3 feet after they enter the house.

15. Use your window coverings.

It’s surprising how much insulation can be provided by curtains, drapes, shades and even mini blinds. Close window coverings this winter at night and when you’re away to conserve heat in the home. In hot weather, close window coverings in the morning to keep the house cool, saving money on air conditioning.